Hi/
Both the PCI slots are running the same controller.
The following is the output from the lspci -vv command
for the ethernet controllers
02:01.0 Ethernet controller: Intel Corp. 82544EI
Gigabit Ethernet Controller (rev 02)
Subsystem: Intel Corp. PRO/1000 XF Server
Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 24
Region 0: Memory at fc220000 (32-bit,
non-prefetchable) [size=128K]
Region 1: Memory at fc200000 (32-bit,
non-prefetchable) [size=128K]
Region 2: I/O ports at 7000 [size=32]
Expansion ROM at <unassigned> [disabled]
[size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2-
AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1
PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit-
133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0,
DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled
Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
02:02.0 Ethernet controller: Intel Corp. 82544EI
Gigabit Ethernet Controller (rev 02)
Subsystem: Intel Corp. PRO/1000 XF Server
Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 28
Region 0: Memory at fc260000 (32-bit,
non-prefetchable) [size=128K]
Region 1: Memory at fc240000 (32-bit,
non-prefetchable) [size=128K]
Region 2: I/O ports at 7020 [size=32]
Expansion ROM at <unassigned> [disabled]
[size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2-
AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1
PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit-
133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0,
DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled
Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
As you can see the capabilites does list PCI-X. I am
currently running BIOS version 1.10 on the
machine.Intel has released a new BIOS 1.12 ;I went
through the release notes and couldnt find anything
which would help.
Any ideas /suggestions.
Please cc: me your replies ; I am not on the Linux
-kernel mailing list.
Thanks
Abhishek
>Not only is the bus running at 66 MHz, it's using the
>PCI protocol not
>?PCI-X. Is there a card in the other PCI-X capable
>slot? I think they
>are on the same bus, so installing a PCI card there
>would bring both
>slots down to this speed. You should check the output
>of lspci -v and
>make sure all the devices on bus 2 have the PCI-X
>capability.
>- Chris Leech
> PCI_Bus_Type PCI
> PCI_Bus_Speed 66MHz
> PCI_Bus_Width 64-bit
-
__________________________________________________
Do You Yahoo!?
Yahoo! Health - Feel better, live better
http://health.yahoo.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Tue Jul 30 2002 - 14:00:24 EST