"PCI: Cannot allocate resource region" messages at boot

From: D. Sen (dsen@homemail.com)
Date: Fri Jul 12 2002 - 10:38:26 EST

I am getting these messages during bootup time on an IBM Thinkpad T30:

Jul 11 17:17:24 calliope kernel: PCI: Cannot allocate resource region 0
of device 02:00.0
Jul 11 17:17:24 calliope kernel: PCI: Cannot allocate resource region 0
of device 02:00.1

lspci -vv identifies these devices as:

02:00.0 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
         Subsystem: IBM: Unknown device 0512
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
         Latency: 168, cache line size 20
         Interrupt: pin A routed to IRQ 11
         Region 0: Memory at d0201000 (32-bit, non-prefetchable) [size=4K]
         Bus: primary=02, secondary=03, subordinate=05, sec-latency=176
         Memory window 0: f0000000-f03ff000 (prefetchable)
         Memory window 1: d0400000-d07ff000
         I/O window 0: 00004000-000040ff
         I/O window 1: 00004400-000044ff
         BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
         16-bit legacy interface ports at 0001

02:00.1 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
         Subsystem: IBM: Unknown device 0512
         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
         Latency: 168, cache line size 20
         Interrupt: pin B routed to IRQ 11
         Region 0: Memory at d0202000 (32-bit, non-prefetchable) [size=4K]
         Bus: primary=02, secondary=06, subordinate=08, sec-latency=176
         Memory window 0: f0400000-f07ff000 (prefetchable)
         Memory window 1: d0800000-d0bff000
         I/O window 0: 00004800-000048ff
         I/O window 1: 00004c00-00004cff
         BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
         16-bit legacy interface ports at 0001

We are also seeing weird PCMCIA behaviour whereby cardmgr does not
detect the insertion and removal of PCMCIA devices. Using the Yenta
socket in the 2.4.18 kernel. Perhaps the boot messages and this
behaviour is related?

DS

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

This archive was generated by hypermail 2b29 : Mon Jul 15 2002 - 22:00:22 EST