Linux version 2.4.10 (root@mackman.net) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-85)) #1 SMP Mon Sep 24 02:37:41 PDT 2001 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002fffe000 (usable) BIOS-e820: 000000002fffe000 - 0000000030000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) found SMP MP-table at 000fe710 hm, page 000fe000 reserved twice. hm, page 000ff000 reserved twice. hm, page 000f0000 reserved twice. On node 0 totalpages: 196606 zone(0): 4096 pages. zone(1): 192510 pages. zone(2): 0 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: DELL Product ID: WS 410 APIC at: 0xFEE00000 Processor #0 Pentium(tm) Pro APIC version 17 Processor #1 Pentium(tm) Pro APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Processors: 2 Kernel command line: BOOT_IMAGE=linux ro root=900 BOOT_FILE=/boot/vmlinuz rootflags=data=journal Initializing CPU#0 Detected 497.436 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 992.87 BogoMIPS Memory: 771836k/786424k available (1015k kernel code, 14204k reserved, 295k data, 196k init, 0k highmem) Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au) mtrr: detected mtrr type: Intel CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU0: Intel Pentium III (Katmai) stepping 03 per-CPU timeslice cutoff: 1461.79 usecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000040 ESR value after enabling vector: 00000000 Booting processor 1/1 eip 2000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 992.87 BogoMIPS CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check reporting enabled on CPU#1. CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU1: Intel Pentium III (Katmai) stepping 03 Total of 2 processors activated (1985.74 BogoMIPS). ENABLING IO-APIC IRQs ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-13, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 number of MP IRQ sources: 41. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 .... register #01: 00170011 ....... : max redirection entries: 0017 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 0 0 0 0 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 0 0 0 0 0 1 1 71 0a 003 03 0 0 0 0 0 1 1 79 0b 003 03 0 0 0 0 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 000 00 1 0 0 0 0 0 0 00 0e 003 03 0 0 0 0 0 1 1 91 0f 003 03 0 0 0 0 0 1 1 99 10 003 03 1 1 0 1 0 1 1 A1 11 003 03 1 1 0 1 0 1 1 A9 12 003 03 1 1 0 1 0 1 1 B1 13 003 03 1 1 0 1 0 1 1 B9 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ16 -> 0:16 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 497.4466 MHz. ..... host bus clock speed is 99.4891 MHz. cpu: 0, clocks: 994891, slice: 331630 CPU0 cpu: 1, clocks: 994891, slice: 331630 CPU1 checking TSC synchronization across CPUs: passed. PCI: PCI BIOS revision 2.10 entry at 0xfcf1e, last bus=2 PCI: Using configuration type 1 PCI: Probing PCI hardware Unknown bridge resource 0: assuming transparent PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 PCI->APIC IRQ transform: (B0,I7,P3) -> 19 PCI->APIC IRQ transform: (B0,I17,P0) -> 19 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 PCI->APIC IRQ transform: (B2,I10,P0) -> 18 PCI->APIC IRQ transform: (B2,I14,P0) -> 18 Limiting direct PCI/PCI transfers. Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Starting kswapd Journalled Block Device driver loaded pty: 256 Unix98 ptys configured block: 128 slots per queue, batch=16 Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller on PCI bus 00 dev 39 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hda: IBM-DTLA-307045, ATA DISK drive hdc: IBM-DTLA-307045, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=5606/255/63, UDMA(33) hdc: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(33) Partition check: hda: hda1 hdc: [PTBL] [5606/255/63] hdc1 SCSI subsystem driver Revision: 1.00 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1 aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs Vendor: IBM Model: DDYS-T09170N Rev: S96H Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DDYS-T09170N Rev: S96H Type: Direct-Access ANSI SCSI revision: 03 scsi0:0:0:0: Tagged Queuing enabled. Depth 253 scsi0:0:1:0: Tagged Queuing enabled. Depth 253 Vendor: YAMAHA Model: CRW4416S Rev: 1.0g Type: CD-ROM ANSI SCSI revision: 02 Vendor: NEC Model: CD-ROM DRIVE:466 Rev: 1.06 Type: CD-ROM ANSI SCSI revision: 02 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 (scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 63, 16bit) SCSI device sda: 17916240 512-byte hdwr sectors (9173 MB) sda: sda1 sda2 sda3 (scsi0:A:1): 80.000MB/s transfers (40.000MHz, offset 63, 16bit) SCSI device sdb: 17916240 512-byte hdwr sectors (9173 MB) sdb: sdb1 sdb2 sdb3 md: raid1 personality registered as nr 3 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: Autodetecting RAID arrays. (read) hda1's sb offset: 45030080 [events: 00000039] (read) hdc1's sb offset: 45030080 [events: 00000039] (read) sda1's sb offset: 2104384 [events: 0000003f] (read) sda2's sb offset: 5799360 [events: 0000003f] (read) sdb1's sb offset: 2104384 [events: 0000003f] (read) sdb2's sb offset: 5799360 [events: 0000003f] md: autorun ... md: considering sdb2 ... md: adding sdb2 ... md: adding sda2 ... md: created md1 md: bind md: bind md: running: md: sdb2's event counter: 0000003f md: sda2's event counter: 0000003f md: RAID level 1 does not need chunksize! Continuing anyway. md1: max total readahead window set to 124k md1: 1 data-disks, max readahead per data-disk: 124k raid1: device sdb2 operational as mirror 0 raid1: device sda2 operational as mirror 1 raid1: raid set md1 active with 2 out of 2 mirrors md: updating md1 RAID superblock on device md: sdb2 [events: 00000040](write) sdb2's sb offset: 5799360 md: sda2 [events: 00000040](write) sda2's sb offset: 5799360 md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind md: bind md: running: md: sdb1's event counter: 0000003f md: sda1's event counter: 0000003f md: RAID level 1 does not need chunksize! Continuing anyway. md0: max total readahead window set to 124k md0: 1 data-disks, max readahead per data-disk: 124k raid1: device sdb1 operational as mirror 1 raid1: device sda1 operational as mirror 0 raid1: raid set md0 active with 2 out of 2 mirrors md: updating md0 RAID superblock on device md: sdb1 [events: 00000040](write) sdb1's sb offset: 2104384 md: sda1 [events: 00000040](write) sda1's sb offset: 2104384 md: considering hdc1 ... md: adding hdc1 ... md: adding hda1 ... md: created md2 md: bind md: bind md: running: md: hdc1's event counter: 00000039 md: hda1's event counter: 00000039 md: RAID level 1 does not need chunksize! Continuing anyway. md2: max total readahead window set to 124k md2: 1 data-disks, max readahead per data-disk: 124k raid1: device hdc1 operational as mirror 1 raid1: device hda1 operational as mirror 0 raid1: raid set md2 active with 2 out of 2 mirrors md: updating md2 RAID superblock on device md: hdc1 [events: 0000003a](write) hdc1's sb offset: 45030080 md: hda1 [events: 0000003a](write) hda1's sb offset: 45030080 md: ... autorun DONE. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with journal data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 196k freed Adding Swap: 1052248k swap-space (priority 1) Adding Swap: 1052248k swap-space (priority 1) usb.c: registered new driver usbdevfs usb.c: registered new driver hub uhci.c: USB UHCI at I/O 0xdce0, IRQ 19 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected uhci.c: :USB Universal Host Controller Interface driver hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: USB device 2 (vend/prod 0x46d/0xc00c) is not claimed by any active driver. usb.c: registered new driver hid input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb1:2.0 hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.10, 23 Sep 2001 on md(9,0), internal journal isapnp: Scanning for PnP cards... isapnp: Card 'CS4236B' isapnp: 1 Plug & Play card detected total ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996 ad1848: No ISAPnP cards found, trying standard ones... kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.10, 23 Sep 2001 on md(9,1), internal journal EXT3-fs: mounted filesystem with journal data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.10, 23 Sep 2001 on md(9,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 00:11.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xdc00. Vers LK1.1.16 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A (scsi0:A:1:0): Locking max tag count at 128 VFS: brelse: Trying to free free buffer