Re: "clock timer configuration lost" on ASUS A7A266

From: Bobby D. Bryant (bdbryant@mail.utexas.edu)
Date: Thu Aug 02 2001 - 10:34:40 EST


Mike Frisch wrote:

> Hardware: ASUS A7A266 (ALiMAGiK chipset), AMD T-Bird 1.2 GHz
> Kernel: 2.4.7-ac2
>
> 'dmesg' frequently reports:
>
> probable hardware bug: clock timer configuration lost - probably a VIA686a motherboard.
> probable hardware bug: restoring chip configuration.

Just FYI, I see the same thing on the same board. My lspci -vv is also attached. Ask if
you need more.

Bobby Bryant
Austin, Texas

00:00.0 Host bridge: Acer Laboratories Inc. [ALi]: Unknown device 1647 (rev 04)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
        Latency: 0
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [b0] AGP version 2.0
                Status: RQ=27 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
        Capabilities: [a4] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5247 (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory behind bridge: dc800000-dddfffff
        Prefetchable memory behind bridge: ddf00000-dfffffff
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:04.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c4) (prog-if fa)
        Subsystem: Asustek Computer, Inc.: Unknown device 8053
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (500ns min, 1000ns max)
        Interrupt: pin A routed to IRQ 0
        Region 4: I/O ports at d400 [size=16]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV]
        Subsystem: Acer Laboratories Inc. [ALi] ALI M1533 Aladdin IV ISA Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [a0] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at b800 [size=256]
        Region 1: Memory at da000000 (32-bit, non-prefetchable) [size=256]
        Expansion ROM at <unassigned> [disabled] [size=64K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 Unknown mass storage controller: Promise Technology, Inc. 20267 (rev 02)
        Subsystem: Promise Technology, Inc.: Unknown device 4d33
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 10
        Region 0: I/O ports at b400 [size=8]
        Region 1: I/O ports at b000 [size=4]
        Region 2: I/O ports at a800 [size=8]
        Region 3: I/O ports at a400 [size=4]
        Region 4: I/O ports at a000 [size=64]
        Region 5: Memory at d9800000 (32-bit, non-prefetchable) [size=128K]
        Expansion ROM at <unassigned> [disabled] [size=64K]
        Capabilities: [58] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Serial controller: US Robotics/3Com 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550])
        Subsystem: US Robotics/3Com: Unknown device 00d7
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 9
        Region 0: I/O ports at 9800 [size=8]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:11.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP (rev 82) (prog-if 00 [VGA])
        Subsystem: Matrox Graphics, Inc.: Unknown device 0641
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (4000ns min, 8000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at de000000 (32-bit, prefetchable) [size=32M]
        Region 1: Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
        Region 2: Memory at dc800000 (32-bit, non-prefetchable) [size=8M]
        Expansion ROM at ddfe0000 [disabled] [size=128K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [f0] AGP version 2.0
                Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/



This archive was generated by hypermail 2b29 : Tue Aug 07 2001 - 21:00:26 EST