No luck with either William's or Agus's suggestions. Still 11 MB/s
transfer rate, dma enabled or not. The motherboard is a newer IWILL.
dmesg outputs:
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD300BB-00AUA1, ATA DISK drive
hdc: Hewlett-Packard CD-Writer Plus 9100b, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: WDC WD300BB-00AUA1, 28629MB w/2048kB Cache, CHS=3649/255/63, UDMA(100)
hdparm -i /dev/hda outputs:
Model=WDC WD300BB-00AUA1, FwRev=18.20D18, SerialNo=WD-WMA6R3063544
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=0
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=58633344
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
UDMA modes: mode0 mode1 mode2 mode3 mode4 *mode5
hdparm -t /dev/hda outputs:
/dev/hda:
Timing buffered disk reads: 64 MB in 5.66 seconds = 11.31 MB/sec
[sigh...]
I suppose it could be the Western Digital disk - I seem to recall that
linux has a difficult history with WD (a comment that may merely start
an unfounded rumour...)
B.D.
On Thu, 22 Mar 2001, William Park wrote:
> On Wed, Mar 21, 2001 at 08:40:21PM -0800, Brian Dushaw wrote:
> > Dear Linux Kernel Wisemen,
> > I have been following the discussion of the VIA vt82c686b chipset
> > and the troubles people have had in getting UDMA(100) to work. This
> > is to report that I have now tried the 2.4.2-ac20 kernel and the
> > 2.2.18 kernel with Andre's patch (dated March 20) and neither of
> > them get the disk speed up to where it ought to be. hdparm -t reports
> > back 11 MB/s or so for either kernel.
> > VIA82CXXX enabled, and I also tried the ide0=ata66 flag, in desparation.
> > At boot up both kernels report the disk as UDMA(100) - everything
> > seems to be peachy keen, but for the sluggish disk performance.
> >
> > Merely a report from the front lines,
>
> Try 'hdparm -d1 -t', and see what you get.
>
> :wq --William Park, Open Geometry Consulting, Linux/Python, 8 CPUs.
>
-- %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%Brian Dushaw Applied Physics Laboratory University of Washington 1013 N.E. 40th Street Seattle, WA 98105-6698 (206) 685-4198 (206) 543-1300 (206) 543-6785 (fax) dushaw@apl.washington.edu
Web Page: http://staff.washington.edu/dushaw/index.html
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Mar 23 2001 - 21:00:17 EST