Aic7xxx troubles with 2.4.1ac6

From: Ville Herva (vherva@viasys.com)
Date: Thu Feb 08 2001 - 06:56:06 EST


It looks like ac6 (which I believe includes the patch you posted) is
still a no-go with 7892. The boot halts and it just prints this once a
second:

(SCSI0:0:3:1) Synchronous at 160 Mbyte/sec offset 31
(SCSI0:0:3:1) CRC error during data in phase
(SCSI0:0:3:1) CRC error in intermediate CRC packet

This happens also with ac5+the small patch you posted earlier. ac2 works
fine (although something did corrupt my MBR while using it. It is still
a complete mystery to me what could have done it. Now I'm unable to
boot NT; linux of course works with the boot floppy.)

ac2 dmesg's:

SCSI subsystem driver Revision: 1.00
(scsi0) <Adaptec AIC-7892 Ultra 160/m SCSI host adapter> found at PCI
3/9/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 392 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.1/5.2.0
       <Adaptec AIC-7892 Ultra 160/m SCSI host adapter>
(scsi0:0:3:0) Synchronous at 80.0 Mbyte/sec, offset 31.
  Vendor: QUANTUM Model: ATLAS 10K 18WLS Rev: UCHK
  Type: Direct-Access ANSI SCSI revision: 03
Attached scsi disk sda at scsi0, channel 0, id 3, lun 0
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
Partition check:
 /dev/scsi/host0/bus0/target3/lun0: p1 p2 p3

cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 5.2.1/5.2.0
Compile Options:
  TCQ Enabled By Default : Enabled
  AIC7XXX_PROC_STATS : Enabled

Adapter Configuration:
           SCSI Adapter: Adaptec AIC-7892 Ultra 160/m SCSI host adapter
                           Ultra-160/m LVD/SE Wide Controller at PCI 3/9/0
    PCI MMAPed I/O Base: 0xfc8ff000
 Adapter SEEPROM Config: SEEPROM found and used.
      Adaptec SCSI BIOS: Enabled
                    IRQ: 10
                   SCBs: Active 0, Max Active 8,
                         Allocated 31, HW 32, Page 255
             Interrupts: 42493
      BIOS Control Word: 0x58a4
   Adapter Control Word: 0x1c5e
   Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
     Ultra Enable Flags: 0x0000
 Tag Queue Enable Flags: 0x0008
Ordered Queue Tag Flags: 0x0008
Default Tag Queue Depth: 8
    Tagged Queue By Device array for aic7xxx host instance 0:
      {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}
    Actual queue depth per device for aic7xxx host instance 0:
      {1,1,1,8,1,1,1,1,1,1,1,1,1,1,1,1}

Statistics:

(scsi0:0:3:0)
  Device using Wide/Sync transfers at 80.0 MByte/sec, offset 31
  Transinfo settings: current(10/31/1/0), goal(10/127/1/0),
user(9/127/1/2)
  Total transfers 42420 (34614 reads and 7806 writes)
             < 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
   Reads: 39 0 25175 3674 4257 946 433 90
  Writes: 0 0 3558 1864 502 480 455 947

cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 03 Lun: 00
  Vendor: QUANTUM Model: ATLAS 10K 18WLS Rev: UCHK
  Type: Direct-Access ANSI SCSI revision: 03

-- 
Ville Herva            vherva@viasys.com             +358-50-5164500
Viasys Oy              Hannuntie 6  FIN-02360 Espoo  +358-9-2313-2160
PGP key available: http://www.iki.fi/v/pgp.html  fax +358-9-2313-2250
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/



This archive was generated by hypermail 2b29 : Thu Feb 15 2001 - 21:00:11 EST