I have a dual Ppro200 with 440FX chipset and an IBM 30GB ide disk. The
kernel is 2.2.18pre18 with no additional patches. DMA appears not to work
with this combination.
lspci:
00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02)
00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]
00:07.2 USB Controller: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] (rev 01)
00:0c.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 02)
00:0d.0 VGA compatible controller: Matrox Graphics, Inc. MGA 2164W [Millennium II]
00:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7871
hdparm -i /dev/hda:
/dev/hda:
Model=IBM-DTLA-305030, FwRev=TW3OA60A, SerialNo=YG0YG017000
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60036480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
hdparm /dev/hda:
/dev/hda:
multcount = 0 (off)
I/O support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
nowerr = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 3737/255/63, sectors = 60036480, start = 0
If I do hdparm -d1; hdparm -tT /dev/hda
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
VFS: Disk change detected on device ide0(3,64)
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: timeout waiting for DMA
hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hda: DMA disabled
ide0: reset: success
On another box with a single PPro200 and 440FX chipset, DMA works just
fine. That box also has IBM disk (30GB) but runs 2.0.37.
Should I try the IDE-patch or suspect the cable? Can anybody confirm that
DMA works with 440FX and a recent 2.2.x?
-- v --
v@iki.fi
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Tue Nov 07 2000 - 21:00:17 EST