Linux version 2.2.15 (root@h0mer.syr.edu) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Fri May 26 03:33:24 EDT 2000
Console: colour VGA+ 80x25
Calibrating delay loop... 66.15 BogoMIPS
Memory: 71444k/73728k available (840k kernel code, 412k reserved, 992k data, 40k init)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry hash table entries: 16384 (order 5, 128k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Cyrix 6x86L 1x Core/Bus Clock stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfdba1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Starting kswapd v 1.5 
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
PIIX3: IDE controller on PCI bus 00 dev 39
PIIX3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: IBM-DJNA-352030, ATA DISK drive
hdc: Maxtor 91152D8, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: IBM-DJNA-352030, 19470MB w/1966kB Cache, CHS=39560/16/63, (U)DMA
hdc: Maxtor 91152D8, 10991MB w/256kB Cache, CHS=22332/16/63, (U)DMA
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
aha152x: processing commandline: ok
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x0: vital data: PORTBASE=0x340, IRQ=11, SCSI ID=7, reconnect=enabled, parity=enabled, synchronous=disabled, delay=100, extended translation=disabled
aha152x: trying software interrupt, ok.
scsi0 : Adaptec 152x SCSI driver; $Revision: 1.7 $
scsi : 1 host.
  Vendor: SEAGATE   Model: ST51080N          Rev: 0958
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: SEAGATE   Model: ST43400N          Rev: 0116
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
  Vendor: QUANTUM   Model: EMPIRE_1080S      Rev: 2000
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
  Vendor: MATSHITA  Model: CD-ROM CR-8005    Rev: 1.0m
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
  Vendor: SEAGATE   Model: ST15230N          Rev: 0298
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 5, lun 0
scsi : detected 1 SCSI cdrom 4 SCSI disks total.
Uniform CDROM driver Revision: 2.56
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2109840 [1030 MB] [1.0 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 5688447 [2777 MB] [2.8 GB]
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 2109376 [1029 MB] [1.0 GB]
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]
eth0: 3c509 at 0x300 tag 1, 10baseT port, address  00 a0 24 e8 9d 4a, IRQ 10.
3c509.c:1.16 (2.2) 2/3/98 becker@cesdis.gsfc.nasa.gov.
Partition check:
 sda: sda1 sda2 < sda5 sda6 sda7 >
 sdb: sdb1 sdb2 < sdb5 sdb6 >
 sdc: sdc1
 sdd: sdd1
 hda: hda1
 hdc: hdc1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 136512k swap-space (priority -1)
eth0: Setting Rx mode to 1 addresses.