I am running into a problem and i was wondering if you might help. I am
installing Linux onto a Gatway 2000 133mhz pc. I am using an Intel
Etherexpress Pro 100 B PCI network card, the only 2 cards in the machine
are PCI (the video card and network card). I installed Slakware off of a
cd-rom i had with no problems... i used the kernal image that supported
networking and ide.
when i use this command to set up the card ifconfig eth0 (ip address)
up
I get this error SIOCSIFADDR : No such device
I looked at a couple how to's and discovered this command
dmesg
I looked and found that i was getting "UNKNOWN PCI DEVICE" errors on
bootup
Is there anything i can do to correct this?
Any Ideas?
Thanks in advance
Mike Ferrari
This is the output
--------------------------
<bigger>Console: colour EGA+ 80x25, 1 virtual console (max 63)
bios32_init : BIOS32 Service Directory structure at 0x000fce80
bios32_init : BIOS32 Service Directory entry at 0xfce90
pcibios_init : PCI BIOS revision 2.10 entry at 0xfceb1
Probing PCI hardware.
Unknown PCI device. PCI Vendor id=8. PCI Device id=7030.
PLEASE MAIL POTTER@CAO-VLSI.IBP.FR your hardware description and
/proc/pci.
Unknown PCI device. PCI Vendor id=8. PCI Device id=7000.
PLEASE MAIL POTTER@CAO-VLSI.IBP.FR your hardware description and
/proc/pci.
Unknown PCI device. PCI Vendor id=8. PCI Device id=1229.
PLEASE MAIL POTTER@CAO-VLSI.IBP.FR your hardware description and
/proc/pci.
Unknown PCI device. PCI Vendor id=11. PCI Device id=3208.
PLEASE MAIL POTTER@CAO-VLSI.IBP.FR your hardware description and
/proc/pci.
Calibrating delay loop.. ok - 53.26 BogoMips
Serial driver version 4.11 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
lp1 at 0x0378, using polling driver
PS/2 auxiliary pointing device detected -- driver installed.
ftape: allocated 3 buffers aligned at: 00218000
hda: WDC AC11000H, 1007MB w/128KB Cache, LBA, CHS=1023/32/63,
MaxMult=16
hdb: WDC AC2635F, 610MB w/64KB Cache, LBA, CHS=620/32/63, MaxMult=16
hdc: TOSHIBA CD-ROM XM-5602B, ATAPI, CDROM drive
ide1: secondary interface on irq 15
ide0: primary interface on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
lance.c: PCI bios is present, checking for devices...
Memory: 14772k/16384k available (760k kernel code, 384k reserved, 468k
data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.019
Swansea University Computer Society TCP/IP for NET3.019
IP Protocols: ICMP, UDP, TCP
PPP: version 0.2.7 (4 channels) NEW_TTY_DRIVERS OPTIMIZE_FLAGS
TCP compression code copyright 1989 Regents of the University of
California
PPP line discipline registered.
SLIP: version 0.8.3-NET3.019-NEWTTY (4 channels) (6 bit encapsulation
enabled)
CSLIP: code copyright 1989 Regents of the University of California
eth0: ewrk3_probe(): Detected a device already registered at 0x160
eth0: ewrk3_probe(): Detected a device already registered at 0x360
eth0: ewrk3_probe(): Detected a device already registered at 0x3c0
eth0: D-Link DE-600 pocket adapter: not at I/O 0x378.
D-Link DE-620 pocket adapter not identified in the printer port
Checking 386/387 coupling... Ok, fpu using exception 16 error
reporting.
Checking 'hlt' instruction... Ok.
Linux version 1.2.13 (root@bigkitty) (gcc version 2.7.0) #1 Wed Aug 23
01:06:43 CDT 1995
Partition check:
hda: multiple mode turned off
hda: hda1 hda2 hda3
hdb: multiple mode turned off
hdb:
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 57452k swap-space
Max size:309790 Log zone size:2048
First datazone:68 Root inode number 139264
ISO9660 Extensions: RRIP_1991A
iBCS: socksys registered on character major 30</bigger>
-
To unsubscribe from this list: send the line "unsubscribe linux-net" in
the body of a message to majordomo@vger.rutgers.edu