[PATCH net v2 1/2] net: dsa: mt7530: fix enabling EEE on MT7531 switch on all boards

[Arınç ÜNAL via B4 Relay]

From: Arınç ÜNAL <arinc.unal@xxxxxxxxxx>

The commit 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features")
brought EEE support but did not enable EEE on MT7531 switch MACs. EEE is
enabled on MT7531 switch MACs either by pulling the LAN2LED0 pin low on the
board (bootstrapping), or unsetting the EEE_DIS bit on the trap register.

There are existing boards that were not designed to pull the pin low.
Therefore, unset the EEE_DIS bit on the trap register.

Unlike MT7530, the modifiable trap register won't be populated identical to
the trap status register after reset. Therefore, read from the trap status
register, modify the bits, then write to the modifiable trap register.

My testing on MT7531 shows a certain amount of traffic loss when EEE is
enabled. That said, I haven't come across a board that enables EEE. So
enable EEE on the switch MACs but disable EEE advertisement on the switch
PHYs. This way, we don't change the behaviour of the majority of the boards
that have this switch.

With this change, EEE can now be enabled using ethtool.

The disable EEE bit on the trap pertains to the LAN2LED0 pin which is
usually used to control an LED. Once the bit is unset, the pin will be low.
That will make the active low LED turn on.

The pin is controlled by the switch PHY. It seems that the PHY controls the
pin in the way that it inverts the pin state. That means depending on the
wiring of the LED connected to LAN2LED0 on the board, the LED may be on
without an active link.

Fixes: 40b5d2f15c09 ("net: dsa: mt7530: Add support for EEE features")
Reviewed-by: Florian Fainelli <florian.fainelli@xxxxxxxxxxxx>
Signed-off-by: Arınç ÜNAL <arinc.unal@xxxxxxxxxx>
---
 drivers/net/dsa/mt7530.c | 14 ++++++++++++++
 drivers/net/dsa/mt7530.h |  1 +
 2 files changed, 15 insertions(+)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 678b51f9cea6..6aa99b590329 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2458,6 +2458,20 @@ mt7531_setup(struct dsa_switch *ds)
 	/* Reset the switch through internal reset */
 	mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
 
+	/* Allow modifying the trap and enable Energy-Efficient Ethernet (EEE).
+	 */
+	val = mt7530_read(priv, MT7531_HWTRAP);
+	val |= CHG_STRAP;
+	val &= ~EEE_DIS;
+	mt7530_write(priv, MT7530_MHWTRAP, val);
+
+	/* Disable EEE advertisement on the switch PHYs. */
+	for (i = MT753X_CTRL_PHY_ADDR;
+	     i < MT753X_CTRL_PHY_ADDR + MT7530_NUM_PHYS; i++) {
+		mt7531_ind_c45_phy_write(priv, i, MDIO_MMD_AN, MDIO_AN_EEE_ADV,
+					 0);
+	}
+
 	if (!priv->p5_sgmii) {
 		mt7531_pll_setup(priv);
 	} else {
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index a71166e0a7fc..509ed5362236 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -457,6 +457,7 @@ enum mt7531_clk_skew {
 #define  XTAL_FSEL_M			BIT(7)
 #define  PHY_EN				BIT(6)
 #define  CHG_STRAP			BIT(8)
+#define  EEE_DIS			BIT(4)
 
 /* Register for hw trap modification */
 #define MT7530_MHWTRAP			0x7804

-- 
2.40.1