[PATCH 5/8] drm/loongson: Using vbios for the LS7A2000 output initialization

[Sui Jingfeng]

For LS7A2000, the built-in VGA encoder is transparent. Connect another
external transmitter with this internal VGA encoder is not sane, thus is
not allowed. Because there are two internal encoders hardware resource on
the first display pipe, call loongson_vbios_query_encoder_info() to know
what exatly the output configutaion is. Either VGA or HDMI display output
interface, but not both. And formal products should not export three
display connector interfaces. As the hardware has two-way I2Cs and two
CRTCs. So with this observation, we can untangle more.

If there a need to extend(transform) the output interface type, then the
internal HDMI phy MUST be enabled and initialized. External transmitters
must take the HDMI signal as input, this is the only choices. Such as
lt6711(HDMI to eDP), lt8619(HDMI to LVDS) etc.

Before apply this patch, ls7a2000_output_init() is simplified function
which assumed that there is no external display bridge attached. This
naive abstraction no longer suit the needs in the long run. Hence, switch
to call the newly implemented lsdc_output_init() function, which allow us
model the external encoder as a drm display bridge. The driver of this drm
display bridge should reside in the same kernel module with drm/loongson.
We will attach it by ourself, and rely on the VBIOS tell us which display
pipe has what display bridge connected.

Signed-off-by: Sui Jingfeng <suijingfeng@xxxxxxxxxxx>
---
 drivers/gpu/drm/loongson/lsdc_output_7a2000.c | 154 ++++++++++++++----
 1 file changed, 124 insertions(+), 30 deletions(-)

diff --git a/drivers/gpu/drm/loongson/lsdc_output_7a2000.c b/drivers/gpu/drm/loongson/lsdc_output_7a2000.c
index ce3dabec887e..bf558b61802b 100644
--- a/drivers/gpu/drm/loongson/lsdc_output_7a2000.c
+++ b/drivers/gpu/drm/loongson/lsdc_output_7a2000.c
@@ -501,6 +501,126 @@ static const struct drm_encoder_helper_funcs ls7a2000_encoder_helper_funcs = {
 	.atomic_mode_set = ls7a2000_hdmi_atomic_mode_set,
 };
 
+/* The built-in tranparent VGA encoder is only available on display pipe 0 */
+static void ls7a2000_pipe0_vga_encoder_reset(struct drm_encoder *encoder)
+{
+	struct lsdc_device *ldev = to_lsdc(encoder->dev);
+	u32 val = PHY_CLOCK_POL | PHY_CLOCK_EN | PHY_DATA_EN;
+
+	lsdc_wreg32(ldev, LSDC_CRTC0_DVO_CONF_REG, val);
+
+	/*
+	 * The firmware set LSDC_HDMIx_CTRL_REG blindly to use hardware I2C,
+	 * which is may not works because of hardware bug. We using built-in
+	 * GPIO emulated I2C instead of the hardware I2C here.
+	 */
+	lsdc_ureg32_clr(ldev, LSDC_HDMI0_INTF_CTRL_REG, HW_I2C_EN);
+
+	mdelay(20);
+}
+
+static const struct drm_encoder_funcs ls7a2000_pipe0_vga_encoder_funcs = {
+	.reset = ls7a2000_pipe0_vga_encoder_reset,
+	.destroy = drm_encoder_cleanup,
+};
+
+static const struct lsdc_output_desc ls7a2000_vga_pipe0 = {
+	.pipe = 0,
+	.encoder_type = DRM_MODE_ENCODER_DAC,
+	.connector_type = DRM_MODE_CONNECTOR_VGA,
+	.encoder_funcs = &ls7a2000_pipe0_vga_encoder_funcs,
+	.encoder_helper_funcs = &lsdc_pipe0_hdmi_encoder_helper_funcs,
+	.connector_funcs = &lsdc_connector_funcs,
+	.connector_helper_funcs = &lsdc_connector_helper_funcs,
+	.name = "VGA-0",
+};
+
+static const struct lsdc_output_desc ls7a2000_hdmi_pipe0 = {
+	.pipe = 0,
+	.encoder_type = DRM_MODE_ENCODER_TMDS,
+	.connector_type = DRM_MODE_CONNECTOR_HDMIA,
+	.encoder_funcs = &lsdc_pipe0_hdmi_encoder_funcs,
+	.encoder_helper_funcs = &lsdc_pipe0_hdmi_encoder_helper_funcs,
+	.connector_funcs = &lsdc_pipe0_hdmi_connector_funcs,
+	.connector_helper_funcs = &lsdc_connector_helper_funcs,
+	.name = "HDMI-0",
+};
+
+static const struct lsdc_output_desc ls7a2000_hdmi_pipe1 = {
+	.pipe = 1,
+	.encoder_type = DRM_MODE_ENCODER_TMDS,
+	.connector_type = DRM_MODE_CONNECTOR_HDMIA,
+	.encoder_funcs = &lsdc_pipe1_hdmi_encoder_funcs,
+	.encoder_helper_funcs = &lsdc_pipe1_hdmi_encoder_helper_funcs,
+	.connector_funcs = &lsdc_pipe1_hdmi_connector_funcs,
+	.connector_helper_funcs = &lsdc_connector_helper_funcs,
+	.name = "HDMI-1",
+};
+
+/*
+ * For LS7A2000, the built-in VGA encoder is transparent. If there are
+ * external encoder exist, then the internal HDMI encoder MUST be enabled
+ * and initialized. As the internal HDMI encoder is always connected, so
+ * only the transmitters which take HDMI signal (such as HDMI to eDP, HDMI
+ * to LVDS, etc) are usable with.
+ */
+const struct lsdc_output_desc *
+ls7a2000_query_output_configuration(struct drm_device *ddev, unsigned int pipe)
+{
+	enum loongson_vbios_encoder_name encoder_name = 0;
+	bool ret;
+
+	ret = loongson_vbios_query_encoder_info(ddev, pipe, NULL,
+						&encoder_name, NULL);
+	if (!ret)
+		goto bailout;
+
+	if (pipe == 0) {
+		switch (encoder_name) {
+		case ENCODER_CHIP_INTERNAL_HDMI:
+			return &ls7a2000_hdmi_pipe0;
+
+		/*
+		 * For LS7A2000, the built-in VGA encoder is transparent.
+		 */
+		case ENCODER_CHIP_INTERNAL_VGA:
+			return &ls7a2000_vga_pipe0;
+
+		/*
+		 * External display bridge exists, the internal HDMI encoder
+		 * MUST be enabled and initialized. Please add a drm bridge
+		 * driver, and attach to this encoder.
+		 */
+		default:
+			return &ls7a2000_hdmi_pipe0;
+		}
+	}
+
+	if (pipe == 1) {
+		switch (encoder_name) {
+		case ENCODER_CHIP_INTERNAL_HDMI:
+			return &ls7a2000_hdmi_pipe1;
+
+		/*
+		 * External display bridge exists, the internal HDMI encoder
+		 * MUST be enabled and initialized. Please add a drm bridge
+		 * driver, and attach it to this encoder.
+		 */
+		default:
+			return &ls7a2000_hdmi_pipe1;
+		}
+	}
+
+bailout:
+	if (pipe == 0)
+		return &ls7a2000_vga_pipe0;
+
+	if (pipe == 1)
+		return &ls7a2000_hdmi_pipe1;
+
+	return NULL;
+}
+
 /*
  * For LS7A2000:
  *
@@ -517,36 +637,10 @@ int ls7a2000_output_init(struct drm_device *ddev,
 			 unsigned int pipe)
 {
 	struct lsdc_output *output = &dispipe->output;
-	struct drm_encoder *encoder = &output->encoder;
-	struct drm_connector *connector = &output->connector;
-	int ret;
-
-	ret = drm_encoder_init(ddev, encoder, &ls7a2000_encoder_funcs[pipe],
-			       DRM_MODE_ENCODER_TMDS, "encoder-%u", pipe);
-	if (ret)
-		return ret;
-
-	encoder->possible_crtcs = BIT(pipe);
-
-	drm_encoder_helper_add(encoder, &ls7a2000_encoder_helper_funcs);
-
-	ret = drm_connector_init_with_ddc(ddev, connector,
-					  &ls7a2000_hdmi_connector_funcs[pipe],
-					  DRM_MODE_CONNECTOR_HDMIA, ddc);
-	if (ret)
-		return ret;
 
-	drm_info(ddev, "display pipe-%u has HDMI %s\n", pipe, pipe ? "" : "and/or VGA");
+	output->descp = ls7a2000_query_output_configuration(ddev, pipe);
+	if (!output->descp)
+		return -EINVAL;
 
-	drm_connector_helper_add(connector, &ls7a2000_connector_helpers);
-
-	drm_connector_attach_encoder(connector, encoder);
-
-	connector->polled = DRM_CONNECTOR_POLL_CONNECT |
-			    DRM_CONNECTOR_POLL_DISCONNECT;
-
-	connector->interlace_allowed = 0;
-	connector->doublescan_allowed = 0;
-
-	return 0;
+	return lsdc_output_init(ddev, dispipe, ddc, pipe);
 }
-- 
2.34.1