Re: [PATCH v2 2/6] riscv: dts: starfive: jh7110: add dc controller and hdmi node

[Emil Renner Berthing]

Keith Zhao wrote:
> Add the dc controller and hdmi node for the Starfive JH7110 SoC.
>
> Signed-off-by: Keith Zhao <keith.zhao@xxxxxxxxxxxxxxxx>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 91 +++++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 41 +++++++++
>  2 files changed, 132 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index de0f40a8b..97909b6d2 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -31,6 +31,25 @@ memory@40000000 {
>  		reg = <0x0 0x40000000 0x1 0x0>;
>  	};
>
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		/* vout applies for space from this CMA
> +		 * Without this CMA reservation,
> +		 * vout may not work properly.
> +		 */
> +		linux,cma {
> +			compatible = "shared-dma-pool";
> +			reusable;
> +			size = <0x0 0x20000000>;
> +			alignment = <0x0 0x1000>;
> +			alloc-ranges = <0x0 0x70000000 0x0 0x20000000>;
> +			linux,cma-default;
> +		};
> +	};
> +
>  	gpio-restart {
>  		compatible = "gpio-restart";
>  		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
> @@ -231,6 +250,41 @@ GPOEN_DISABLE,
>  			slew-rate = <0>;
>  		};
>  	};
> +
> +	hdmi_pins: hdmi-0 {
> +		hdmi-scl-pins {
> +			pinmux = <GPIOMUX(0, GPOUT_SYS_HDMI_DDC_SCL,
> +					     GPOEN_SYS_HDMI_DDC_SCL,
> +					     GPI_SYS_HDMI_DDC_SCL)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-sda-pins {
> +			pinmux = <GPIOMUX(1, GPOUT_SYS_HDMI_DDC_SDA,
> +					     GPOEN_SYS_HDMI_DDC_SDA,
> +					     GPI_SYS_HDMI_DDC_SDA)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-cec-pins {
> +			pinmux = <GPIOMUX(14, GPOUT_SYS_HDMI_CEC_SDA,
> +					     GPOEN_SYS_HDMI_CEC_SDA,
> +					     GPI_SYS_HDMI_CEC_SDA)>;
> +			input-enable;
> +			bias-pull-up;
> +		};
> +
> +		hdmi-hpd-pins {
> +			pinmux = <GPIOMUX(15, GPOUT_HIGH,
> +					     GPOEN_ENABLE,
> +					     GPI_SYS_HDMI_HPD)>;
> +			input-enable;
> +			bias-disable; /* external pull-up */
> +		};
> +	};
> +

Please don't break the alphabetical ordering of these nodes.

>  };
>
>  &uart0 {
> @@ -254,3 +308,40 @@ &U74_3 {
>  &U74_4 {
>  	cpu-supply = <&vdd_cpu>;
>  };
> +
> +&voutcrg {
> +	status = "okay";
> +};
> +
> +&display {
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hdmi_pins>;
> +
> +	hdmi_in: port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		hdmi_in_dc: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&dc_out_hdmi>;
> +		};
> +	};
> +};
> +
> +&dc8200 {
> +	status = "okay";
> +
> +	dc_out: port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		dc_out_hdmi: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&hdmi_in_dc>;
> +		};
> +
> +	};
> +};

Some goes for these node references. The order is /-node, clocks, node refences
sorted alphabetically.


> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 0005fa163..1670452fb 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -282,6 +282,11 @@ tdm_ext: tdm-ext-clock {
>  		#clock-cells = <0>;
>  	};
>
> +	display: display-subsystem {
> +		compatible = "starfive,display-subsystem";
> +		ports = <&dc_out>;
> +	};
> +
>  	soc {
>  		compatible = "simple-bus";
>  		interrupt-parent = <&plic>;
> @@ -613,5 +618,41 @@ voutcrg: clock-controller@295c0000 {
>  			#reset-cells = <1>;
>  			power-domains = <&pwrc JH7110_PD_VOUT>;
>  		};
> +
> +		dc8200: lcd-controller@29400000 {
> +			compatible = "starfive,jh7110-dc8200";
> +			reg = <0x0 0x29400000 0x0 0x100>,
> +			      <0x0 0x29400800 0x0 0x2000>;
> +			interrupts = <95>;
> +			clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_DISP_AXI>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX1>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_CORE>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_AXI>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_AHB>,
> +				<&hdmitx0_pixelclk>,
> +				<&voutcrg JH7110_VOUTCLK_DC8200_PIX>;
> +			clock-names = "noc_bus", "channel0", "channel1",
> +				      "dc_core", "axi_core", "ahb",
> +				      "hdmi_tx", "dc_parent";
> +			resets = <&voutcrg JH7110_VOUTRST_DC8200_AXI>,
> +				 <&voutcrg JH7110_VOUTRST_DC8200_AHB>,
> +				 <&voutcrg JH7110_VOUTRST_DC8200_CORE>;
> +			reset-names = "axi","ahb", "core";
> +		};
> +
> +		hdmi: hdmi@29590000 {
> +			compatible = "starfive,jh7110-inno-hdmi";
> +			reg = <0x0 0x29590000 0x0 0x4000>;
> +			interrupts = <99>;
> +
> +			clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
> +				 <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
> +				 <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
> +				 <&hdmitx0_pixelclk>;
> +			clock-names = "sysclk", "mclk", "bclk", "pclk";
> +			resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
> +			#sound-dai-cells = <0>;
> +		};

These nodes, however, are sorted by their address which you alse break in this
patch :(

>  	};
>  };
> --
> 2.34.1
>